English
Русский
Español
العربية
Steel Angle Punching Machine
All marking, punching and shearing in automatic completeness, all finished angles can be unloaded by pneumatic turnover device so as to lighten the working strength.
6. The control system consists of the host computer, servo motor, PLC, external examination sensors, etc. Just input the dimension of workpiece, the processing will be created. Furthermore, the program can be stored, selected, displayed and communicated as per the workpiece No.
Marking unit adopts closed frame with good rigidity. Four groups of character boxes are fixed on the marking unit which can be selected by program.
8. TAPM1612C is single blade shearing. The punching, marking and shearing cylinders are bigger;
9. With avoided shearing functions, so as to process fixed-length angles.
2. Basic configuration of the machine
2.1 Mechanical part
| No. | Item | YJX1010 |
| 1 | Total length | 24200mm |
| 2 | Quantity of feeding table | 3 group |
| 3 | Quantity of overturning tables | 3 group |
| 4 | Quantity of feeding driver | 1 group |
| 5 | Length of feeding passage | 15800mm |
| 6 | Length of the host | 2100mm |
| 7 | Length of finished passage | 6m |
| 8 | Pneumatic control system | 1 Group |
| 9 | Hydraulic control system | 1 Group |
| 10 | Feeding direction | According to user requirements |
| 11 | Integrated hydraulic station | Yes |
| 12 | The purchaser is responsible for the part | Embedded plates and anchor bolts required for the cement foundation and equipment of the installation site shall be prepared according to the foundation drawing provided by the supplier |
2.2 Electronic control part
| 1 | Numerical Control System | PLC Control System |
| 2 | Driving System | Panasonic Servo Motor |
3. Technical parameters of the machine
| No. | Item | Commodity |
| YJX1010 | ||
| 1 | Angle Beam Range(Mm) | 38*38*3-100*100*10 |
| 2 | Max Punching Diameter | Φ26mm(Q235, Q345), punching of special-shaped holes and oblong holes can be achieved by changing the mold |
| 3 | Max Punching force(KN) | 700KN |
| 4 | Punching Side | 2 Sides |
| 5 | Number of die per side | 3 Pcs |
| 6 | Typing ability(KN) | 700KN |
| 7 | Qty of typing groups | 4 Groups |
| 8 | Digit number of each group | 12 Pcs |
| 9 | Character size | (L*W*H)14*10*19mm |
| 10 | Shearing force(KN) | 1250KN |
| 11 | Shearing method | Single Blade Shearing |
| 12 | CNC Axis | 3 Axis |
| 13 | Length of Blank Workpiece(M) | 12 M |
| 14 | Max Length of Workpiece(M) | 12 M |
| 15 | Length of finished workpiece(M) | 10 M |
| 14 | Discharging method of finished products | The finished material channel is pushed manually and turned out to one side. The power source for turning out is pneumatic. |
| 16 | Angle Beam feeding speed | Max 90m/min |
| Punching speed(times/min) | Average 50-60 times/min | |
| 17 | Programming Mode | Input by keyboard, RS232, CAD floppy disk input &USB interface |
| 18 | Lubrication method | Equipped with automatic lubrication |
| 19 | Fabrication Precision | Hole diameter tolerance: 0-0.8mm |
| Dmax-Dmin: ≤1.2mm Aperture roundness tolerance range: Dmax-Dmin: ≤1.2mm | ||
| Hole perpendicularity error: ≤0.36mm | ||
| Distance tolerance of two adjacent holes in the same group: ±0.5mm | ||
| The hole distance tolerance of two non-adjacent holes in the same group: ±0.7mm | ||
| End distance tolerance : ±1.2mm | ||
| Shearing length tolerance: ±1mm | ||
| Verticality of cut surface: ≤1.2mm |
4. Working Environment
| 1 | Power Supply | 3 Phase 4 Wire System |
| 2 | Voltage | 415V±10% |
| 3 | Frequency | 50Hz |
| 4 | Operating temperature | 0℃-40℃ |
| 5 | Relative Humidity | <90% No condensation |
| 6 | Air Compressed | Pressure: 0.8MPa Flow rate: 1.0m³/h |
5. Machine Configuration Introduction
YJX-1610 New Type High-Speed CNC Angle Steel Punching Typing & Shearing Machine is mainly composed of feeding table, turning feeding table, feeding channel, feeding trolley, punching unit, typing unit, shearing unit, finished material channel, electrical system, hydraulic system, etc.
