English
Русский
Español
العربية
CNC Marking Punching and Shearing Machine for Angle
cnc marking punching drilling and cutting machine for angle Application: Used to punch holes on the sides of angle beam profile.
Components: It is composed of punching cylinder, column plate, mold base, Bracket, indenter, worktable, etc.
There are two or three sets of punching dies on each side, and two or three punches with different diameters can be installed.
cnc angle punching machine application: It is used to drive the mold base to move along the screw direction to control the punching criterion.
Drive mode: Panasonic servo motor drive.
Transmission mode: precision screw transmission.
Protection measures: Dust-proof bearings are used in the bearing housing, and the sheet metal shield prevents the servo motor from being polluted by dust.
2.1 Mechanical part
| No. | Item | YJX2020S |
| 1 | Total length | 29000mm |
| 2 | Quantity of feeding table | 4 group |
| 3 | Quantity of overturning tables | 4 group |
| 4 | Quantity of feeding driver | 1 group |
| 5 | Length of feeding passage | 16000mm |
| 6 | Length of the host | 2200mm |
| 7 | Length of finished passage | 10m |
| 8 | Pneumatic control system | 1 Group |
| 9 | Hydraulic control system | 1 Group |
| 10 | Feeding direction | According to user requirements |
| 11 | Integrated hydraulic station | No |
| 12 | The purchaser is responsible for the part | Embedded plates and anchor bolts required for the cement foundation and equipment of the installation site shall be prepared according to the foundation drawing provided by the supplier |
2.2 Electronic control part
| 1 | Numerical Control System | PLC Control System |
| 2 | Driving System | Panasonic Servo Motor |
3. Technical parameters of the machine
| No. | Item | Commodity |
| YJX2020 | ||
| 1 | Angle size Range(mm) | 56*56*4-200*200*20 |
| 2 | Max Punching Diameter | Φ25.5mm(Q235, Q345), punching of special-shaped holes and oblong holes can be achieved by changing the mold |
| 3 | Max Punching force(KN) | 1000KN |
| 4 | Punching Side | 2 Sides |
| 5 | Number of die per side | 3 Pcs |
| 6 | Typing ability(KN) | 1030KN |
| 7 | Qty of typing groups | 4 Groups |
| 8 | Digit number of each group | 12 Pcs |
| 9 | Character size | (L*W*H)14*10*19mm |
| 10 | Shearing force(KN) | 1500KN |
| 11 | Shearing method | Double Blade Shearing |
| 12 | CNC Axis | 3 Axis |
| 13 | Length of Blank Workpiece(M) | 12 M |
| 14 | Max Length of Workpiece(M) | 12 M |
| 15 | Length of finished workpiece(M) | 10 M |
| 14 | Discharging method of finished products | The finished material channel is pushed manually and turned out to one side. The power source for turning out is pneumatic. |
| 16 | Angle Beam feeding speed | Max 90m/min |
| 17 | Programming Mode | Input by keyboard, RS232, CAD floppy disk input &USB interface |
| 18 | Lubrication method | Equipped with automatic lubrication |
| 19 | Fabrication Precision | Hole diameter tolerance: 0-0.8mm |
| Dmax-Dmin: ≤1.2mm Aperture roundness tolerance range: Dmax-Dmin: ≤1.2mm | ||
| Hole perpendicularity error: ≤0.36mm | ||
| Distance tolerance of two adjacent holes in the same group: ±0.5mm | ||
| The hole distance tolerance of two non-adjacent holes in the same group: ±0.7mm | ||
| End distance tolerance : ±1.2mm | ||
| Shearing length tolerance: ±1mm | ||
| Verticality of cut surface: ≤1.2mm |
4. Working Environment
| 1 | Power Supply | 3 Phase-4 Wire system |
| 2 | Voltage | 415V±10% |
| 3 | Frequency | 50Hz |
| 4 | Operating temperature | 0℃-40℃ |
| 5 | Relative Humidity | <90% No condensation |
| 6 | Air Compressed | Pressure: 0.8MPa Flow rate: 1.0m³/h |
5. Machine Configuration Introduction
YJX-1616 New Type High-Speed CNC Angle Steel Punching Typing & Shearing Production Line is mainly composed of feeding table, turning feeding table, feeding channel, feeding trolley, punching unit, typing unit, shearing unit, finished material channel, electrical system, hydraulic system, etc.
