CNC Hydraulic Plate Punching Machine Model YBJ100

YBJ CNC Hydraulic Plate Punching Machine

1. Brief Introduction:

The YBJ cnc hydraulic connecting plate punching device is regularly used inside the production of iron/metal towers within the electricity transmission and transformation enterprise and the manufacturing of steel structural components in the construction and bridge industries. it is specially used for punching, drilling and typing of connecting plates.

2. Machine Model and Configuration

2.1 Mechanical Part

No.	Item	YBJ100	YBJZ100	YBJ120D	YBJ120
1	Machine Layout Area	5*3.5 M			5*4.5 M
2	No. of Hosts	1 set
3	No. of Workbench Bases	1 set
4	No. of Y-Slide	1 set
5	No. of X-direction Slide	1 set
6	No. of Clamps	2 sets
7	No. of drilling spindle heads	NO	1 set	NO
8	Pneumatic control system	1 set
9	Hydraulic control system	1 set
10	Buyer Preparation Working	Installation Site-cement foundation, embedded slabs and anchor bolts required by equipment, make the foundation according to the foundation plan provided by the supplier

2.2 Electronic Control Part

1	CNC Controller system	PLC control system
2	Drive System	Panasonic Servo Motor

3. The main technical parameters of the machine

No.	Item	YBJ100	YBJZ100	YBJ120D	YBJ120
1	Processing plate size	1500*800mm			1500*1500mm
2	Processing plate thickness	5-25mm
3	Punching force	1000KN		1200KN
4	Maximum punching (drilling) hole diameter	Φ26mm	Φ26mm Drilling OD Φ50	Φ26mm	Φ30mm-25mm Φ40mm-20mm
5	Total number of modules	3 Pcs	4 Pcs	3 Pcs
6	Number of punching die	2 Pcs			3 Pcs
7	Number of print header groups	1 Group			NO
8	Prefix	10 Pcs			NO
9	Header size	（L*W*H）14*10*19mm			NO
10	Number of CNC axes	2
11	X, Y axis servo motor power	2*2KW
12	X, Y axis feeding speed	20m/min
13	Punching speed	50-55 Times/Min
14	Total weight of equipment	6T	6.5T	7.8T	9.5T

4. Machine working environment

1	Power supply	3 Phase 4-Wire System
2	Voltage	3 Phase 380V±10%
3	Frequency	50Hz
4	Operating Temperature	0℃-40℃
5	Relative Humidity	＜90% no condensation
6	Compressed Air	Pressure: 0.8MPa Flow rate: 0.1m³/min

5. Machine parts introduction

The equipment is mainly composed of Punching Host Unit, Workbench Moving Unit, Clamp Assembly, Pneumatic System, Electrical System, Hydraulic System, etc.

6. List of main accessories

1. Machine layout diagram/drawing

2. Machine Tools List.

No.	Commodity&Specification	Qty	Mark/Note
1	Punch rod (including nut)	1 Set	Accessories
2	Prefix (number, English)	1 Set/Each	Including installed on the machine
3	Upper jaw, lower jaw	2 Pcs/Each	Accessories
4	Punch (φ17.5, φ21.5, φ25.5)	1 Pcs/Each	Including installed on the machine
5	Die (φ19.5, φ23.5, φ24.7, φ27.5, φ28.7, φ29.5)	1 Pcs/Each	Including installed on the machine
6	Quick change drill chuck	1 Set	Including installed on the machine (only available for YBJZ100 model)
7	Typing pad	1 Pcs	Accessories
8	Open-end wrench	1 Pcs	Opening 41mm
9	Hexagonal Wrench	1 set
10	"十" screwdriver	1 Pcs
11	"一" screwdriver	1 Pcs
12	Proximity switch	2 Pcs
13	Air torch	1 Pcs
14	Mechanical manual	1 Set
15	Electrical manual	1 Set
16	Packing List	2 set	Attached to the manual
17	Certificate	2 Pcs