English
Русский
Español
العربية
CNC Marking Punching and Shearing Machine for Angle Channel and Flat Bar
Application: It is used for punching the other flange of Angle steel and two flange of channel steel.
The unit consists of a base, a column, a moving beam, a fixed beam and a side punch mechanism.The side punch mechanism and the moving beam are connected by the linear guide rail and the slide block, and the side punch mechanism adjusts the clearance between the punching die frame and the plate through the floating mechanism.The moving beam moves up and down through the ball screw driven by the servo motor, and the holes of different heights can be washed out.
Application: For cutting material
The machine is equipped with channel steel cutting tool, strip steel cutting tool and Angle steel cutting tool.Channel tools are divided into several groups, each group corresponds to a type of channel steel.Channel tools are combined tools.All the cutting tools can be used in reverse position, greatly improving the utilization rate of the blade and saving cost.
2. Basic configuration of the machine
2.1 Mechanical part
| Serial No. | Item | YJCX18 |
| 1 | Total length | 21.5m |
| 2 | Quantity of feeding table | 4 group |
| 3 | Quantity of feeding driver | 1 group |
| 4 | Length of feeding passage | 13140mm |
| 5 | Length of the host | 2850mm |
| 6 | Length of finished passage | 5000mm |
| 7 | Pneumatic control system | 1group |
| 8 | Hydraulic control system | 1group |
| 9 | Feeding direction | According to user requirements |
| 10 | The purchaser is responsible for the part | Embedded plates and anchor bolts required for the cement foundation and equipment of the installation site shall be prepared according to the foundation drawing provided by the supplier |
2.2 Electronic control part
| 1 | Numerical control system | PLC control system |
| 2 | Drive system | Panasonic servo motor |
3. Technical parameters of the machine
| Serial No. | Item | YJCX18 |
| 1 | Angle steel size(mm) | L63*4-L140*10 |
| 2 | Channel steel size(mm) | 8#-18# |
| 3 | Band steel size(mm) | 60*5-180*10 |
| 4 | Max.length of blank(mm) | 9000 |
| 5 | Max Punching Diameter(mm) | Φ26(Top punching long hole22*60, Side punching long hole 22*40) |
| 6 | Top punching force(KN) | 1000 |
| 7 | Side punching force(KN) | 700+700 |
| 8 | Shearing force | 1500 |
| 9 | Number of punch surface | 3 |
| 10 | Qty.of punch on each side(piece) | 4+2+2 |
| 11 | Qty. of typing character(piece) | 10 characters in two rows |
| 12 | Qty of typing groups | 1 Group |
| 13 | The number of CNC Axis | 3Axis |
| 14 | Min. length of shearing residue(mm) | 50 |
| 15 | Shearing method | Single Blade Shearing |
| 16 | Hydraulic system pressure(MPa) | 25 |
| 17 | Cooling way of hydraulic system | Water cooling |
| 18 | Pneumatic system pressure(MPa) | 0.8 |
| 19 | Driver feeding speed(m/min) | Max.90 |
| 20 | Punching frequency(time/min) | 40-50 |
| 21 | Length of finished Workpiece(mm) | 5000 |
| 22 | Total motor power(kw) | ≈42 |
| 20 | total weight(kg) | 11000 |
| 21 | Programming Mode | Input by keyboard, RS232, CAD floppy disk input &USB interface |
| 22 | Lubrication way | Equipped with automatic lubrication |
| 23 | Machining precision | Hole diameter tolerance: 0-0.8mm |
| Dmax-Dmin: Dmax-Dmin: ≤1.2mm | ||
| Angle alignment deviation: ≤0.7mm | ||
| Hole perpendicularity error: ≤0.03tmm(t is the thickness of workpiece), And no more than 2mm |
4. Working Environment
| 1 | Power Supply | Three-phase four-wire system |
| 2 | Voltage | 380V±10% |
| 3 | Frequency | 50Hz |
| 4 | Operating temperature | 0℃-40℃ |
| 5 | Relative Humidity | <90% No condensation |
| 6 | Air Compressed | Pressure: 0.8MPa Flow rate: 1.0m³/h |
5. Introduction of each component of machine
The machine is mainly composed of feeding part, feeding part, main engine part, finished product feeding part, electrical control part, hydraulic power part.
